This page needs to be properly filled according to the New Device Howto and the New Device Page guide.

If a device is special, then feel free to provide a terse description of what makes this device so special. But terse, no novels, no marketing blurb.

Identification

Inet d71
Manufacturer	Manufacturer
Dimensions	188mm x 117mm x heightmm
Release Date	Month year
Website	Device Product Page
Specifications
SoC	A23 @ 1.5Ghz
DRAM	512MiB DDR3 @ xxxMHz
NAND	8GB
Power	DC 5V @ 2A, 2800mAh 3.7V Li-Ion battery
Features
LCD	800x480 (7" 16:9)
Touchscreen	5-finger capacitive (Manufacturer device)
Audio	3.5mm headphone plug, internal speaker, internal microphone
Network	WiFi 802.11 b/g/n (Manufacturer device)
Storage	µSD
USB	1 USB2.0 OTG
Camera	0.3MP (640x480) front
Other	Accelerometer (Manufacturer device)
Headers	UART?

This section explains how to most easily identify your device. For a development board, explain the name(s) printed on the board. For an android device, find out the strings as reported under settings.

On the back of the device, the following is printed:

Azpen
A728

The PCB has the following silkscreened on it:

INET-D71-REV01 Zeng-gc 2013-10-31

In android, under Settings->About Tablet, you will find:

Model Number: A728
Build Number: A23_D71_D711C_PG_1401072.20140616

Sunxi support

Current status

Give a brief overview of the current status of support under sunxi here. If there is mainline support for either U-Boot or kernel, mention this too, but add the extra sections below.

Images

Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be left blank.

HW-Pack

Add MANUFACTURER DEVICE HW-pack specifics here. This section can be left blank.

BSP

Add MANUFACTURER DEVICE BSP specifics here. This section can be left blank.

Manual build

For building U-Boot, use the MANUFACTURER_DEVICE target.
The .fex file can be found in sunxi-boards as MANUFACTURER_DEVICE.fex

Everything else is the same as the manual build howto.

Mainline U-Boot

If there is mainline U-Boot support, add this section.

For building mainline U-Boot, use the MANUFACTURER_DEVICE target.

Don't forget to add

[[Category:Mainline_U-Boot]]

at the bottom of the page.

Mainline kernel

If there is mainline kernel support, add this section.

Use the FAMILY-CHIP-DEVICE.dtb device-tree file for the mainline kernel.

Don't forget to add

[[Category:Mainline_Kernel]]

at the bottom of the page.

Tips, Tricks, Caveats

Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.

FEL mode

The VOL+ button triggers FEL mode.

Device specific topic

If there are no further device specific topics to add, remove these sections.

...

Adding a serial port (voids warranty)

DEVICE UART pads

This section explains how to attach a serial port to the device. Make sure it refers to our UART howto. For a development board, you can just mention how to find the header with the pins and include a picture, and you can remove the warranty voiding warning.

Device disassembly

If necessary, provide a short description of how to open the device. Perhaps explain how the pins can be most easily popped. If pins do need to be popped, mention the Plastic tool howto.

Insert a plastic tool (I used my fingernail) into the seam between the display bezel and the back cover.
Slide the tool around all four sides
When all clips are released, the back cover should lift off. Be careful of the speaker taped to the back.

Locating the UART

Describe how to find the RX,TX,GND signals here, and mention the UART howto.

Pictures

Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.

Also known as

3GO 7003 EQC

Azpen A72

Danew Dslide 750 7.85"

Pixor Tiny One

Serioux Surya Antares 7" Slim SMO72

Serioux Surya Antares 7" Slim SMO9VDC

Inet d71

Contents