KLIPAD SMART i746
| KLIPAD SMART i746 | |
|---|---|
 | |
| Manufacturer | Klipad [1] |
| Dimensions | width 189mm x length 119mm x height 11mm |
| Release Date | 2018 |
| Website | klipad.fr [2] |
| Specifications | |
| SoC | A64 @ 1.152Ghz |
| DRAM | 1GiB DDR3 |
| NAND | 8GB |
| Power | DC 5V @ 1.5A, 2500mAh 3.7V Li-Ion battery |
| Features | |
| LCD | WidthxHeight (7" X:Y) |
| Touchscreen | X-finger capacitive (Manufacturer device) |
| Video | None |
| Audio | 3.5mm headphone plug, internal speaker, internal microphone |
| Network | WiFi 802.11 b/g/n and Bluetooth (RTL8703BS) |
| Storage | µSD |
| USB | 1 x USB2.0 OTG |
| Camera | 2MP GC2035 front, 0.3MP rear |
| Other | Accelerometer (Manufacturer device) |
This page needs to be properly filled according to the New Device Howto and the New Device Page guide.
If a device is special, then feel free to provide a terse description of what makes this device so special. But terse, no novels, no marketing blurb.
Identification
This section explains how to most easily identify your device. For a development board, explain the name(s) printed on the board. For an android device, find out the strings as reported under settings.
On the back of the device, the following is printed:
- KLIVER - Model: KL3839/I746
The PCB has the following silkscreened on it:
YA7001B R600 2018-02-06
In android, under Settings->About Tablet, you will find:
- Model Number: DEVICE
- Build Number: SOC_BOARD_DEVICE_*.*
Sunxi support
Current status
Nothing yet
Images
Optional. Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be removed.
Manual build
You can build things for yourself by following our Manual build howto and by choosing from the configurations available below.
U-Boot
Sunxi/Legacy U-Boot
Use the MANUFACTURER_DEVICE build target.
Mainline U-Boot
Use the MANUFACTURER_DEVICE build target.
Linux Kernel
Sunxi/Legacy Kernel
Use the MANUFACTURER_DEVICE.fex file.
Mainline kernel
Use the FAMILY-CHIP-DEVICE.dtb device-tree binary.
Tips, Tricks, Caveats
Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.
FEL mode
The Volume+ and Power buttons trigger FEL mode. Press and hold `Volume+` Press and hold `Power` for about 2 seconds Release `Power` and press it again 3 times immediately
Device specific topic
If there are no further device specific topics to add, remove these sections. Delivered with a keyboard
...
Adding a serial port (voids warranty)
This section explains how to attach a serial port to the device. Make sure it refers to our UART howto. For a development board, you can just mention how to find the header with the pins and include a picture, and you can remove the warranty voiding warning. Not found how to add a serial port on this device.
Device disassembly
If necessary, provide a short description of how to open the device. Perhaps explain how the pins can be most easily popped. If pins do need to be popped, mention the Plastic tool howto. Warning, plastic is not great. Almost every pins were broken after disassembly. Disassemble by pressing a pry tool between the screen and the back of the tablet.
Locating the UART
Describe how to find the RX,TX,GND signals here, and mention the UART howto. Not found
Pictures
Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.
Also known as
List rebadged devices here.
See also
Add some nice to have links here. This includes related devices, and external links.
Manufacturer images
Optional. Add non-sunxi images in this section.