Sinovoip Banana Pi BPI-6204
| Sinovoip Banana Pi BPI-6204 | |
|---|---|
 | |
| Manufacturer | Sinovoip |
| Dimensions | 105mm x 145mm x 36mm |
| Release Date | ~May 2024 |
| Website | BPI-6202/6204 Product Page |
| Specifications | |
| SoC | A40i @ 1.2Ghz |
| DRAM | 2GiB DDR3 (SK Hynix KH5TQ4G83EFR-RDC x4) |
| NAND | 8GB eMMC 5.1 (Samsung KLM8G1GETF-B041) |
| Power | DC 24V @ 1A |
| Features | |
| Video | HDMI 1.4 (Type A - full) |
| Network | WiFi 802.11 b/g/n (AMPAK AP6212) 10/100/1000Mbps Ethernet (Realtek RTL8211E) 10/100 Ethernet (IC+ IP101GR) Bluetooth4.0 (AMMPAK AP6212) |
| Storage | MicroSD (up to 64 GB) M.2 (B-Key) SSD SATA |
| USB | 2x USB2.0 Host USB2.0 OTG |
| Other | M.2 (B-Key) for 4G/5G LTE w/micro SIM 4x RS485, RS232, CAN |
| Headers | GPIO, SPI |
This page needs to be properly filled according to the New Device Howto and the New Device Page guide.
Industrial controller with full-featured SCADA system
The used SoC is a A40i, but that seems to be the same as the R40 except with industrial temperature range.
Identification
The PCB has the following silkscreened on the front:
CSA6204-A0 scada
Sunxi support
Current status
Give a brief overview of the current status of support under sunxi here.
Images
Optional. Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be removed.
HW-Pack
Optional. Add MANUFACTURER DEVICE sunxi HW-pack specifics here. When empty, this section can be removed.
BSP
Optional. Add MANUFACTURER DEVICE sunxi BSP specifics here. When empty, this section can be removed.
Manual build
You can build things for yourself by following our Manual build howto and by choosing from the configurations available below.
U-Boot
Sunxi/Legacy U-Boot
Only useful for A10/A10s/A13 and A20 based devices. Remove this section otherwise.
Use the MANUFACTURER_DEVICE build target.
Mainline U-Boot
Use the MANUFACTURER_DEVICE build target.
Linux Kernel
Sunxi/Legacy Kernel
Only useful for A10/A10s/A13 and A20 based devices. Remove this section otherwise.
Use the MANUFACTURER_DEVICE.fex file.
Mainline kernel
Use the FAMILY-CHIP-DEVICE.dtb device-tree binary.
Tips, Tricks, Caveats
Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.
FEL mode
The something button triggers FEL mode.
Device specific topic
If there are no further device specific topics to add, remove these sections.
...
Adding a serial port (voids warranty)
This section explains how to attach a serial port to the device. Make sure it refers to our UART howto. For a development board, you can just mention how to find the header with the pins and include a picture, and you can remove the warranty voiding warning.
Device disassembly
If necessary, provide a short description of how to open the device. Perhaps explain how the pins can be most easily popped. If pins do need to be popped, mention the Plastic tool howto.
Locating the UART
Describe how to find the RX,TX,GND signals here, and mention the UART howto.
Pictures
Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.
Schematic
See also
Sinovoip Banana Pi M2 Berry
Sinovoip Banana Pi M2 Ultra
Device page on Banana Pi Wiki
Official Forum