Yones Toptech BS1078

From linux-sunxi.org
Jump to: navigation, search
Yones Toptech BS1078
2015-01-03 11.50.32.jpg
Manufacturer Manufacturer
Dimensions 10.31 in x 6.5 in x 0.43 in (26.2 cm x 16.5 cm x 1.1 cm)
Release Date Month year
Website

Device Product Page

Software
Specifications
SoC A31s @ 1Ghz (Quad-core Cortex-A7)
DRAM 1GB Elixir DDR3-1600 or (2x Elpida J4216BFBG-GN-F) (In IROPRO: 2x Elpida J4216BBBG-DJ-F)
NAND

Micron MLC 16GB / 32GB or (2x SH hynix H27UCG8T2ETR)

(In IROPRO: INTEL 29F16B08CCME2)
Power

DC 5V @ 2A, 6800mAh 3.7V Li-Ion polymer battery

(In IROPRO: 6000mAh MODEL:25A0F0 SIZE:90x150x2.5mm)
Features
LCD

LCD 16:9,resolution1024*600

(In IROPRO: boe10.1g40p-wjs)
Touchscreen

5-point capacitive touchscreen (Silead GSL3635)

(In IROPRO: YTG-P10025-F1 V1.0 Chipset: SILEAD GSL3675)
Video Mini HDMI 1.4a 120Hz 720p (Type C)
Audio 3.5mm headphone plug, Stereo out through Mini HDMI (Type C), internal stereo speakers (8ohm 0.5w each), internal microphone
Network WiFi 802.11 b/g/n Realtek RTL 8723AS 150mbit/s
Storage External and internal MicroSD card slot expansion (2 expansion slots) SD v3.0
Camera 2.0MP (0.3MP 640x480 upscaled to 2MP 1600x1200) rear, 0.3MP (640x480) 1/6.5" CMOS VGA GC0307 front camera module

This page needs to be properly filled according to the New Device Howto and the New Device Page guide.

This is a cheap but very good tablet. It has features wich you cannot find in expensive tablets like HDMI, 3D over HDMI etc. Of course it has downsides like low volume speakers, 40nm CPU Die-shrink etc.

Contents

Identification

In android, under Settings->About Tablet, you will find:

  • Model Number: BS1078

Information about the Android firmware: http://www.androiddevice.info/submission/18763/show

On the PCB (Poofek 10.1", also note that the main chip is epoxy-covered) the following is printed: V5-YONESTOPTECH-BS1078-20140901

Sunxi support

Current status

Give a brief overview of the current status of support under sunxi here. If there is mainline support for either u-boot or kernel, mention this too, but add the extra sections below.

Images

Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be left blank.

HW-Pack

Add MANUFACTURER DEVICE HW-pack specifics here. This section can be left blank.

BSP

Add MANUFACTURER DEVICE BSP specifics here. This section can be left blank.

Manual build

  • For building u-boot, use the MANUFACTURER_DEVICE target.
  • The .fex file can be found in sunxi-boards as yonestoptech_bs1078.fex

Everything else is the same as the manual build howto.

Mainline U-Boot

If there is mainline u-boot support, add this section.

For building mainline u-boot, use the MANUFACTURER_DEVICE target.

Don't forget to add
[[Category:Mainline_U-Boot]]
at the bottom of the page.

Mainline kernel

If there is mainline kernel support, add this section.

Use the FAMILY-CHIP-DEVICE.dtb device-tree file for the mainline kernel.

Don't forget to add
[[Category:Mainline_Kernel]]
at the bottom of the page.

Tips, Tricks, Caveats

Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.

FEL mode

The something button triggers FEL mode.

Device specific topic

If there are no further device specific topics to add, remove these sections.

...

Adding a serial port (voids warranty)

DEVICE UART pads

This section explains how to attach a serial port to the device. Make sure it refers to our UART howto. For a development board, you can just mention how to find the header with the pins and include a picture, and you can remove the warranty voiding warning.


Device disassembly

Unscrew 2 screws on the side with the ports, then using small plastic tool open the cover.

Locating the UART

The RX and TX connections are labeled and on the front of the mainboard (just above the CPU). The large copper trace on the edge where the connectors are can be used as a ground. Refer to the UART howto for more information.

HYPER TERMINAL SETUP: 115200 8-N-1 Xon/Xoff

Pictures

Also known as

Poofek 10.1"

See also

Yones Toptech BD1078

Manufacturer images

Optional. Add non-sunxi images in this section.

Personal tools
Namespaces

Variants
Actions
Navigation
Tools