Warning: apc_store(): GC cache entry 'sunxi-mw:messages:en' was on gc-list for 3610 seconds in /srv/http/sunxi/linux-sunxi.org/wiki/includes/objectcache/APCBagOStuff.php on line 59
Xunlong Orange Pi Win - linux-sunxi.org

Xunlong Orange Pi Win

From linux-sunxi.org
Jump to: navigation, search
Xunlong Orange Pi Win
Device front.jpg
Manufacturer OrangePi
Dimensions 93mm x 60mm
Release Date March 2017 (Plus version in April 2017)
Website [1]
Specifications
SoC A64 @ 1.2 GHz
DRAM 1GiB/2GiB DDR3L
Power DC 5V @ 2A (4.0mm/1.7mm barrel plug - centre positive)
or via µUSB or via Li-battery header pins
Features
Video HDMI (HDCP, CEC), CVBS
Audio 3.5 mm Jack, HDMI, Microphone
Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212), 10/100/1000Mbps Ethernet (Realtek RTL8211E)
Storage µSD, 16Mbit NOR Flash on board
USB 4 USB 2.0 Host (shared, internal hub), 1 USB 2.0 OTG

Orange Pi Win and Orange Pi Win Plus are A64 based development board produced by Xunlong. The Win model comes with 1 GiB of RAM and the Win Plus model is bundled with 2 GiB RAM.

This page needs to be properly filled according to the New Device Howto and the New Device Page guide.

Contents

Identification

The PCB has the following silkscreened on it:

Orange pi Win v1.1

Sunxi support

Current status

The board is supported by both mainline U-Boot and kernels.

Images

Optional. Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be removed.

HW-Pack

Optional. Add MANUFACTURER DEVICE sunxi HW-pack specifics here. When empty, this section can be removed.

BSP

Optional. Add MANUFACTURER DEVICE sunxi BSP specifics here. When empty, this section can be removed.

Manual build

You can build things for yourself by following our Manual build howto and by choosing from the configurations available below.

U-Boot

Sunxi/Legacy U-Boot

Mainline U-Boot

Use the orangepi_win_defconfig build target (supported since v2017.07).

Linux Kernel

Sunxi/Legacy Kernel

Mainline kernel

Use the sun50i-a64-orangepi-win.dtb device-tree tree binary.

Tips, Tricks, Caveats

Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.

FEL mode

The SW3(unsoldered) button triggers FEL mode (untested).

Device specific topic

If there are no further device specific topics to add, remove these sections.

Locating the UART

DEVICE UART pads

The UART pins are located between microusb and power jack of the board. On some boards they are marked as TX, RX and GND on the PCB (simplified layout: ..DC-IN.. [GND][RX][TX] ..microusb..). Just attach some leads according to our UART howto.

Pictures

Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.

Variants

Xunlong Orange Pi Win Plus

  • There is a variant called Xunlong Orange Pi Win Plus with 2 GB of DDR3 instead of the 1 GB in the original version. The Win Plus PCB is also black compared to the original blue. Otherwise the board seems identical.

See also

Manufacturer images

Personal tools
Namespaces

Variants
Actions
Navigation
Tools