This page needs to be properly filled according to the New Device Howto and the New Device Page guide.

Identification

Jepower T508A
Manufacturer	Jepower
Dimensions	350mm x 185mm x 145mm
Release Date	Month year
Website	Device Product Page
Specifications
SoC	A10 @ 1Ghz
DRAM	1GB DDR3 @ xxxMHz
NAND	4GB
Power	DC 12V @ 5A, 4400mAh ?V Li-Ion battery
Features
LCD	1024x720 (9.7")
Touchscreen	5-finger capacitive/resistive (Manufacturer device)
Video	HDMI (mini)
Audio	3.5mm headphone plug, 3.5mm microphone plug, miniHDMI, internal stereo speakers
Network	WiFi 802.11 b/g/n (Realtek RTL8188CUS), 10/100/1000Mbps Ethernet (Realtek RTL8150)
Storage	µSD
USB	3 USB2.0 Host, 1 USB2.0 OTG
Camera	2MP front (optional)
Other	10-digit LED, NFC, RFID, Magnetic stripe reader (optional), RJ11, Fingerprint reader (optional), Thermal printer
Headers	UART, JTAG, LCD, VGA, ...

On the back of the device, the following is printed:

Android Multi-function Intelligent Terminal

Input: 12V5A DC
Model: T508
S/N  : <sticker>

The PCB has the following silkscreened on it:

In android, under Settings->About Tablet, you will find:

Model Number: 363LB POS v1
Build Number: crane_m1003h6-eng 4.1.1 JRO03C 20130108 test-keys

Sunxi support

Current status

Give a brief overview of the current status of support under sunxi here. If there is mainline support for either U-Boot or kernel, mention this too, but add the extra sections below. A10 (sun4i)

Images

Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be left blank.

HW-Pack

Add MANUFACTURER DEVICE HW-pack specifics here. This section can be left blank.

BSP

Add MANUFACTURER DEVICE BSP specifics here. This section can be left blank.

Manual build

For building U-Boot, use the MANUFACTURER_DEVICE target.
The .fex file can be found in sunxi-boards as MANUFACTURER_DEVICE.fex

Everything else is the same as the manual build howto.

Mainline U-Boot

If there is mainline U-Boot support, add this section.

For building mainline U-Boot, use the MANUFACTURER_DEVICE target.

Don't forget to add

[[Category:Mainline_U-Boot]]

at the bottom of the page.

Mainline kernel

If there is mainline kernel support, add this section.

Use the FAMILY-CHIP-DEVICE.dtb device-tree file for the mainline kernel.

Don't forget to add

[[Category:Mainline_Kernel]]

at the bottom of the page.

Tips, Tricks, Caveats

Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.

FEL mode

The something button triggers FEL mode.

Device specific topic

If there are no further device specific topics to add, remove these sections.

...

Adding a serial port (voids warranty)

DEVICE UART pads

This section explains how to attach a serial port to the device. Make sure it refers to our UART howto. For a development board, you can just mention how to find the header with the pins and include a picture, and you can remove the warranty voiding warning.

Device disassembly

If necessary, provide a short description of how to open the device. Perhaps explain how the pins can be most easily popped. If pins do need to be popped, mention the Plastic tool howto.

Locating the UART

Describe how to find the RX,TX,GND signals here, and mention the UART howto.

Pictures

Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.

Jepower T508A

Contents