Inet D71b

From linux-sunxi.org
Jump to navigation Jump to search
Inet D71b
Device front.jpg
Manufacturer Manufacturer
Dimensions widthmm x breadthmm x heightmm
Release Date Month year
Website Device Product Page
Specifications
SoC AXX @ XGhz
DRAM 512MiB/1GiB/2GiB DDR3 @ xxxMHz
NAND 2/4/8/16GB
Power DC 5V @ 3A, 3700mAh 3.7V Li-Ion battery
Features
LCD WidthxHeight (X" X:Y)
Touchscreen X-finger capacitive/resistive (Manufacturer device)
Video HDMI (Type A/B/C - full/mini/micro), VGA
Audio 3.5mm headphone plug, 3.5mm microphone plug, HDMI, SPDIF, internal stereo speakers, internal speaker, internal microphone
Network WiFi 802.11 b/g/n (Manufacturer device), 10/100/1000Mbps Ethernet (Manufacturer device)
Storage µSD, SATA
USB X USB2.0 Host, X USB2.0 OTG
Camera  ??.?MP (????x????) front, ??.?MP (????x????) rear
Other Accelerometer (Manufacturer device), GPS, IRDA
Headers UART, JTAG, LCD, VGA, ...

This page needs to be properly filled according to the New Device Howto and the New Device Page guide.

Identification

This section explains how to most easily identify your device. For a development board, explain the name(s) printed on the board. For an android device, find out the strings as reported under settings.

On the back of the device, the following is printed:

Pendo Pad
PENDHD7

The PCB has the following silkscreened on it:

Inet D71B-Rev02 Zeng-gc 2014-11-06

In android, under Settings->About Tablet, you will find:

  • Model Number: DEVICE
  • Build Number: SOC_BOARD_DEVICE_*.*

Sunxi support

Current status

Give a brief overview of the current status of support under sunxi here.

Images

Optional. Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be removed.

HW-Pack

Optional. Add MANUFACTURER DEVICE sunxi HW-pack specifics here. When empty, this section can be removed.

BSP

Optional. Add MANUFACTURER DEVICE sunxi BSP specifics here. When empty, this section can be removed.

Manual build

You can build things for yourself by following our Manual build howto and by choosing from the configurations available below.

U-Boot

Sunxi/Legacy U-Boot

Use the MANUFACTURER_DEVICE build target.

Mainline U-Boot

Use the MANUFACTURER_DEVICE build target.

Linux Kernel

Sunxi/Legacy Kernel

Use the MANUFACTURER_DEVICE.fex file.

Mainline kernel

Use the FAMILY-CHIP-DEVICE.dtb device-tree binary.

Tips, Tricks, Caveats

Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.

FEL mode

The something button triggers FEL mode.

Device specific topic

If there are no further device specific topics to add, remove these sections.

...

Adding a serial port (voids warranty)

DEVICE UART pads

This section explains how to attach a serial port to the device. Make sure it refers to our UART howto. For a development board, you can just mention how to find the header with the pins and include a picture, and you can remove the warranty voiding warning.

Device disassembly

If necessary, provide a short description of how to open the device. Perhaps explain how the pins can be most easily popped. If pins do need to be popped, mention the Plastic tool howto.

Locating the UART

Describe how to find the RX,TX,GND signals here, and mention the UART howto. See UART howto. Easiest way to find the signals is to remove the 5 screws and the touch sense flatflex and fold the board up. They are marked on the underside of the board.

Pictures

Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.

Also known as

List rebadged devices here.

See also

Add some nice to have links here. This includes related devices, and external links.

Manufacturer images

Optional. Add non-sunxi images in this section.